Please Note: We try to provide every kind of tips and secrets related to various Siemens Mobile. All these Secrets are taken from trusted sources and we have also tested many of them but still we can’t guarantee if they will work properly for you. Feel free to take these tips and try on your own risk. We won’t be held responsible for any damages caused to your mobile phone. Hopefully nothing such will happen

Siemens S3 comfort:

Show IMEI code: * # 06 #

MONITOR MODE:

The Siemens S3 Com series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.

TO ACTIVATE MONITOR MODE:

1. Turn the phone on.

2. Enter the PIN access code on press OK. (Only if is enabled).

3. Press Menu. (Left top button).

4. Press 9. (Phone Options).

5. Press 8. (Phone Status) (May be button 7 in some phones).

6. You may see your IMEI Number

7. Left Display Button (Top left MENU key).

8. 7684666

9. HangUp Button. (Red HandSet key).

Note: Monitor should appear now at the bottom of the Network Options menu.

MONITOR MODE TOGGLE:

Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Tips and tricks:

Nice Sunset in the display. Siemens S3 or younger

In the Telephone Book in the section own numbers, first position you have to type in +12022243121 (Number of the Capitol in Washington DC) and save it without a name. Then open this telephone book again do so as you like to change the number but leave the modus without changing anything. A nice Sundown will be shown in the display.

Pin Out:

1- GND

2- SB

3- POWER

4- NC

5- TX

6- RX

7- CLOCK

8- DATA

9- GND MIC

10- HF MIC

11- AUDIO

12- GND AUDIO

Please Note: We try to provide every kind of tips and secrets related to various Siemens Mobile. All these Secrets are taken from trusted sources and we have also tested many of them but still we can’t guarantee if they will work properly for you. Feel free to take these tips and try on your own risk. We won’t be held responsible for any damages caused to your mobile phone. Hopefully nothing such will happen

Siemens s3 and Siemens s3 Comfort:

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Tetris:

Power on phone andv enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4.

Monitor Mode:

1. Menu

2. 9 (Phone Options)

3. 7 (Phone Status)

4. Left Display Button (left MENU key)

5. 5553756

6. HangUp Button (Red HandSet key)

Now “Monitor” should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress )

CH Channel Number

RX Signal Strength (dB)

N NCC (Color Code)

B BCC (Color Code)

CI Cell ID (in Hex)

C1+ how long before phone does forced hand over. (see RX and RXAM)

LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC

TXPWR Transmit Power (dB)

RXAM Reeceive signal strength cut-off point

TS* Time Slot Number

TA* Timing Advance. Distance from tower in Km * 2

PL* Power Level

Power Table:

PL: 5 6 7 8 9 10 11 12 13 14 15

dB: 33 31 29 27 25 23 21 19 17 15 13

Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF* C1 value with continuous transmisson from tower

LS* C1 Value with discontinuous tranmission from tower

QF* Bit Error Rate with continuous transmission from tower

QS* Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) table

QF/QS register: 0 1 2 3 4 5 6 7

% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Unlock Siemens S3(Not S3 COM)

(For advanced users only)

At addresses 0D8 to 0DD the phones code is stored. To read the code swap nibbles stored at addresses from 0DA to 0DD. Error counter is at 0D9. To clear the Phone Code write at addresses from 0D8 to 0DD: 00, 00, FF, FF, FF, FF.

More coming in next post