Please Note: We try to provide every kind of tips and secrets related to various Motorola Mobile Models. All these Secrets are taken from trusted sources and we have also tested many of them but still we can’t guarantee if they will work properly for you. Feel free to take these tips and try on your own risk. We won’t be held responsible for any damages caused to your mobile phone. Hopefully nothing such will happen

MOTOROLA MICRO-TAC “FLIP” SERIES ( continue ):

40# Receive one voice channel word, when the word is received it will be displayed in hex. Command terminates when the word has been received or when # is pressed.

41# (F19CTA models only) Enables the diversity antenna option on mobiles so equipped.

42# Disable diversity.

43# Disable diversity and force the mobile to use the TRANSMIT antenna.

44# Disable diversity and force the mobile to use the RECEIVE antenna.

45# Display the RSSI reading taken on the current channel.

46# Display the cumulative call timer.

47A# Set audio level to A where A = 0 lowest, A = 6 highest, or A = 7 muted.

48# Turn sidetone on

49# Sidetone off

50# Maintenance data is transmitted and test results displayed: PASS =Received data is correct, FAIL1 = No data received within 2 seconds, FAIL2 = Received data is incorrect.

51# Maintenance data is transmitted and looped back and test results displayed: PASS = Looped back data is correct, FAIL1 = No data looped back within 2 seconds, FAIL2 = Looped back data is incorrect.

52A# Set phase adjustment. A decimal number thet corresponds to phase shift compensation in 4.5 degree increments. Compensation added to the inherant phase shift of the tranceiver to acheive a total phase shift of 0 (zero) degrees. Do not enter any value other than from the following list:

# entered, Degree of shift

0 0 59 121.5 86 243.0

1 4.5 60 126.0 87 247.5

2 9.0 61 130.5 112 252.0

3 13.5 62 135.0 113 256.5

4 18.0 63 139.5 114 261.0

5 22.5 40 144.0 115 265.5

6 27.0 41 148.5 116 270.0

7 31.5 42 153.0 117 274.5

16 36.0 43 157.5 118 279.0

17 40.5 44 162.0 119 283.5

18 45.0 45 166.5 120 288.0

19 49.5 46 171.0 121 292.5

20 54.0 47 175.5 122 297.0

21 58.5 64 180.0 123 301.5

22 63.0 65 184.5 124 306.0

23 67.5 66 189.0 125 310.5

48 72.0 67 193.5 126 315.0

49 76.5 68 198.0 127 319.5

50 81.0 69 202.5 104 324.0

51 85.5 70 207.0 105 328.5

52 90.0 71 211.5 106 333.0

53 94.5 80 216.0 107 337.5

54 99.0 81 220.5 108 342.0

55 103.5 82 225.0 109 346.5

56 108.0 83 229.5 110 351.0

57 112.5 84 234.0 111 355.5

58 117.0 85 238.5

53# Enable scrambler option, if equipped.

54# Disable scrambler option, if equipped.

55# Test Mode programming.

58# Compandor on. Audio compressor and expandor on.

59# Compandor off. Audio compressor and expandor off.

61# Serial number transfer, not all models.

62# Turn on audio ringer path.

63# Turn off audio ringer path.

70# Abbreviated field transmitter audio deviation command for tranceivers with FCC ID: ABZ89FT5668.

71# Abbreviated field power adjustment command for tranceivers with FCC ID: ABZ89FT5668.

72# Field audio phasing command.

73# Field power adjustment command.

Please Note: We try to provide every kind of tips and secrets related to various Motorola Mobile Models. All these Secrets are taken from trusted sources and we have also tested many of them but still we can’t guarantee if they will work properly for you. Feel free to take these tips and try on your own risk. We won’t be held responsible for any damages caused to your mobile phone. Hopefully nothing such will happen

MOTOROLA MICRO-TAC “FLIP” SERIES: ( continue )

MOTOROLA TEST MODE COMMANDS:

01# RESTART (POWER OFF THEN ON)

02# STATUS DISPLAY, ALTERNATES BETWEEN:

ABC DEF where:

ABC = Channel number

DEF = Received sensitivity for that channel

and: A B C D E F G where:

A = SAT frequency (0=5970, 1=6000, 2=6030, 3=no channel lock)

B = Carrier (0=off, 1=on)

C = Signalling tone (0=off, 1=on)

D = Power level (0 through 7)

E = Channel mode (0=voice channel, 1=control channel)

F = Receive audio mute (0=unmuted, 1=muted)

G = Transmit audio mute (0=unmuted, 1=muted)

Press * to hold display and # to end.

03# Reset call timers

04# Initialize Tranceiver to following settings:

Carrier = OFF

Receive Audio = MUTED

Transmit Audio = MUTED

Signaling Tone = OFF

Call Timer RESET and peroiodic resetting ENABLED

SAT = OFF

DTMF & Audio Tones = OFF

Audio Path = To SPEAKER

05# Turn Carrier ON

06# Turn Carrier OFF

07# Mute RECEIVE audio

08# Unmute RECEIVE audio

09# Mute TRANSMIT audio

10# Unmute TRANSMIT audio

11ABC# Load Synthesizer with ABC, where ABC=the channel number in decimal

12A# Set RF power level to A, where A=1 to 7

13# Power down phone

14# Transmit signaling tone

15# Stop transmit of signaling tone

16# Transmit a five word reverse voice channel message, all words will be: “FF00AA55CC33″

17# Transmit a two word reverse voice channel message, both words will be: “FF00AA55CC33″

18# Display contents of NAM one address at a time, press * to advance, press # to exit. (Two digit number to the left is the ADDRESS, to the right is the DATA)

19# Display software version

20# Receive control channel messages counting correctable and uncorrectable errors. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display two three digit numbers. The first number is the number of correctable errors and the second is uncorredtable errors.

21# Receive voice channel messages counting correctable and uncorrectable errors. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display two three digit numbers. The first number is the number of correctable errors and the second is uncorredtable errors.

22# Receive control channel messages counting word sync sequences. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display the number of word sync sequences in the display.

23# Receive voice channel messages counting word sync sequences. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display the number of word sync sequences in the display.

24# Turn SAT transmission ON

25# SAT OFF

27# Transmit continuous control channel data, all words are: “FF00AA55CC33″. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Press # to terminate the test.

28# Activate high tone (1150 Hz +/- 55 Hz)

29# Deactivate high tone

30# Activate low tone (770 Hz +/- 40 Hz)

31# Deactivate low tone

32# Initialize all non-volatile memory to zeros. Resets unit and makes it look “new”.

33A# Activate DTMF tone where A = DTMF digit 0 thru 9

34# Deactivate DTMF

35A# Send audio path to A where A = 0 for handsfree, 1 for speaker, 2 for alert, 3 for Handset

36ABC# Activate channel scan, ABC is scan speed in milliseconds. Tunes from channel 1 to 666. Press * to pause scan and display RSSI, if scan speed is 300 milliseconds or greater the RSSI is displayed with each channel, if scan is less than 300 milliseconds the RSSI is only displayed when you press *

37# not used

38# Display serial number in hex (ESN). Displayes the byte number in the upper right side of the display and the data to the left, press * to step through the bytes, press # to exit.

39# Receive one control channel word, when the word is received it will be displayed in hex. Command terminates when the word has been received or when # is pressed.